Flexibilisation of biogas plants

In contrast to solar and wind power plants, biogas plants can be flexibly and demand-controlled. The EEG 2012 promotes the flexibility of biogas plants. With the flexibility, a cogeneration unit´s generation power is dimensioned larger than required by the rated electrical power. In times of higher electricity prices, more electricity can thus be produced (positive control power) and at times of lower revenue, the system can be run at partial load or switched off, (negative control power).

These additional marketing revenues depend on the technical option for the flexible operation of the system (control power, rate of performance change, gas storage capacity).
In order to increase the performance of the plant, corresponding tests on storage capacities and plant control (24h timetable) must be verified by an environmental verifier.

 

Stepstones for Flexibilisation of biogas plants

Registration to the Federal power grid Network Agency

For a flexible Operation of a cogeneration unit, accompanied by a performance increase, including new approvals; it is first to register with the Federal power grid Network Agency in a so called "market master data Register" (here: registration link). There is to mention the planned start of the flex-opreation with max. three months in advance.



For the evaluation of conformity valid Official documentation is required:

1. Approval of plant extension and flex operation
2. Specification of the installed power and planned rated power
3. Acceptance protocol of the cogeneration plant by the approval authority, if applicable
4. Commissioning protocols of the plant
5.Technical data of the emergency device
6. Gas storage / net gas storage volume verification
7. Location plan / Plant flow diagram / R & I shedule
8. Incident concept, if applicable, or description of incident report
9.If required, adaptation of the risk assessment and the explosion protection documentation
(Fire protection concept, operating instructions and operating instructions for flexible operation)
10.The following test reports, evidence by TÜO or authorized experts:
§14 BetrSichV (before commissioning)
§15 BetrSichV (recurring examination)
§29 BImSchG safety-related commissioning
§17 AwSV test report
risk assessments
TRGS 529 Training with written commissioning of the staff
11.Assurance certificate



Other regulatory approvals, if applicable

1.Veterinary authorization
2. Details of related manure and quantities of renewable sources






Data sheets of the CHP

1.Data sheets cogeneration plant (with flow rate and gas consumption / h)
2.Average methane content
3.Set ignition and support firing (if applicable)
4.Adaptation of the heating concept for flexible operation
5.Measuring technology gas storage tank level




Network operator

1.detection of the claim of the market premium (e.g., last billing network operator)
2.Network connection contract) / Information Grid operator feed-in / grid connection commitment
3. Form Application Federal Network Agency / Confirmation Federal Network Agency
4.Type test confirmation transformer / data sheet transformer or information network operator to the transformer
5.Direktvermarktungsvertrag
6. Plant certificate (if W > 1 MW el)
7. Indication of the amount of electricity produced (operator) / billing network operator
8.Development claim market premium (e.g., last billing network operator)
9.Instructions for plant control and process control technology


Possibly. additional documents after consultation

 

 

Proof of CHP flexibility

In order to prove the flexibility of the system and to apply for the flex bonus, a demonstration operation of at least 3 days must be carried out and documented. In at least one of the following operating conditions, an environmental verifier must assess the operation on site

1. The proof of the displacement potential
With normal feed, the Biogas plant gas storage is depleted to at least 20% of the gas storage volume.
(When the engines are switched off, the time must be determined until the gas storage volume is filled again)


2. Discovering a timetable-controlled mode of operation
In consultation with the direct marketer, a timetable must be arranged for 24 hours, which takes into account the load cases "engines off", "half load" and "full load", and at the same time represents an effective additional revenue over the period.
In another 24h timetable, the operating conditions provided by the plant operator are to be mapped. Here, a real operating plan of the required load conditions, such as e.g. external heat emission


3. Präqualifikation
The pre-qualification proof defines the operating conditions along a so-called double hump.
To do this, each CHP must start from 0 to full load within 5 minutes, run for at least 10 minutes at full load and restart within 5 minutes after and after 10 minutes. This procedure should be repeated once more after 10 minutes.




These 3 operating states are not related in time and can therefore be carried out independently of each other. The 15-minute values ​​of the power feed-in must be requested from the direct marketer and attached to the documentation of the demonstration operation to be validated.

 

 

QHSE cert Division
EU

conformity inspection body
conformity assessment body
Environmental Verifying
Accredited European Certification

Your specific search query will interconnect you with several suggestions to your concern
office cert Division
+49 (0) 231 952 99 4 98